Once you have completed the preparation stage which include measuring exactly how much artificial grass you will need, installing appropriate drainage (if needed) and taking out the natural grass layer, you will be able to install your artificial grass lawn. This article outlines the steps you ought to follow to help you to get the job done right, from laying the base, connecting joints and protecting against unwanted weeds.

Lay Gravel Base then Sharp Sand – If required, use treated timber/timber stakes to place within an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and two X 2 inches of tantalised timber once and for all draining areas. Screw these timbers to the stakes leaving the stakes on the inside the perimeter. In case the Artificial Grass meet a concrete path, wall or decking, position the timber flush with the surface height and also by using 10mm temporary fillet, pack the timber near to the wall leaving the space to enable you to tuck the Artificial Grass between the timber and the adjoining material at a later stage.

Position the stakes up against the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly below the timber edging. Next screw the timber stake towards the timber edging. With heavy clay soils we recommend laying a crushed stone surface of up to 3 inches. This is definitely not necessary for the majority of areas and merely required if you have a very high water table where ground holds water for a long period of your time after it rains. Next compact the ground using a vibrating plate that may be hired from an equipment hire company. Make sure the perimeter is compacted and beneath the timber edging by 1 inch. Infill the perimeter with sharp sand and level employing a rake. Make sure the sand is level to the peak from the timber edging and compact again.

Once and for all drainage areas spread a layer of sharp sand to blind within the soil. Next compact the ground using a vibrating plate that may be hired from an equipment hire company. Guarantee the perimeter is compacted and level using the timber edging. If you put more operate in at this stage, your Artificial Grass Lawn will appear better consequently.

Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails towards the timber edging. This weed control geo textile membrane prevents any possibility of weed growth through the artificial grass drainage holes.

Roll out Artificial Grass – Lay the Artificial Grass within the desired direction working on the carpet rather than on the levelled base. Ensure the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by no less than 4 inches. If the artificial grass meets a path or edge, and for those who have laid the timber edging correctly as previously described, then this artificial grass could be wedged between. If joining, please ensure that the artificial turf installation thousand oaks is laid with all the pile running in the same direction on every piece. Lay the carpet on the top of the sand as opposed to dragging it throughout the base material. To help stop wrinkles or creasing it is best to allow 2 to three hours to settle before continuing with jointing and adhesive. Cut grass to shape utilizing a sharp Dolphin or Stanley knife or scissors.

Jointing – When jointing your outdoor carpet together, ensure the pile runs within the same direction. Shut down manufacturer’s edge strip (if present) and butt two edges together ensuring you will find no gaps more than 1mm between the two carpet edges. The precision of this determines how visible the join is after the completion. Fold back edges and position jointing tape (smooth side down) in order that the edges in the carpet fulfill the tape when joined.

Adhesive – a) Apply the cartridge adhesive in a zig zag motion onto the rougher side in the tape allowing one cartridge for every 3 linear metres. Turn down carpet and press both edges in to the wet adhesive, ensuring each piece marries up and it has no overlap. When you are carrying this out along with your fingers, mix the fibres together to conceal the join. After the whole length is within place and also you are pleased featuring its appearance it is actually required to walk along the join repeatedly to activate the glue and bond the grass towards the tape. Weigh on the seam to make sure good exposure to the glue until it cures. The more care taken with all the operation the neater and tidier the joint will likely be.

b) If making use of the 2-component multi-purpose adhesive, ensure thorough mixing of the two components before use. Apply adhesive for the rough side from the tape and spread evenly across a width of at least 20cm using if at all possible a notched trowel. Sufficient adhesive ought to be applied so that when the artificial grass carpet is pressed to the adhesive, a transfer on the xggnvo backing is finished. Reject carpet and press both edges into the wet adhesive, ensuring each piece marries up and it has no overlap. Ensure that the carpet does not crest on the seam and is also holding flat over the bonded area. After the whole length is at place and also you are happy featuring its appearance it is necessary to walk over the join several times to activate the glue and bond the grass for the tape. Weight the seam to make certain good connection with the glue until it cures. The better care taken using the operation the neater and tidier the joint is going to be.

As you should endeavour never to put adhesive on the carpet small quantities of glue are easy to remove from the artificial grass fibre using White Spirit and a small off cut from the artificial grass. Small amounts of cured glue normally can be removed. To avert this situation and the possibility of injury to the artificial grass, care and precautions ought to be delivered to avoid contact with the fibres all the time. Once the artificial grass has become jointed and glued and you also are happy with all the levels screw the grass towards the timber perimeter framework using galvanised screws at a minimum of 12 inch intervals.

Spread Sand (Optional, depending on Grass Selected) – Once the artificial grass has been laid use silica sand, that is kiln dried and brush into carpet as you go. Each product might have sand infill but this can be only employed to stabilise the carpet and also at virtually no time should the sand be visible. You must get an even spread on the surface employing a brush to build up the depth in layers. Do not apply the sand in a single application. Brush sand into pile immediately after laying while the artificial grass is dry and while weather conditions are good. Brush vigorously against the fibres from the carpet pile to let the tufts to face upright. Putting the proper level of sand in helps support the artificial grass to bed down, protects the fibres and also keeps them standing to give it the style of real grass.